Do you want to continue (y/n) [n]? Table 20-9 show ip pimsm interface vlan Output Details, Table 20-10 show ip pimsm interface stats Output Details. This example assumes that you havent any preconfigured community names or access rights. Figure 3-2 provides an example. Also described in this chapter are port link flap detection, port mirroring, and transmit queue monitoring and how to configure them. Configuring SNMP security model and security level used to request access. Use the set sntp trustedkey command to add an authentication key to the trusted key list. set system lockout emergency-access username 5. show mac [address mac-address] [fid fid] [port port-string] [type {other | learned | self | mgmt | mcast}] 2. Optionally, configure authentication and/or timer values for the virtual link. MultiAuth idle-timeout Specifies the period length for which no traffic is received before a MultiAuth session is set to idle. Rules in an ACL are order-dependent. Configuring Authentication If VLAN authorization is not enabled, the tunnel attributes are ignored. It provides the performance and reliability you expect from the data center, but optimized for office environments, with physical security and whisper-quiet operation. assign ingress vlan using: set port vlan [port-string] X port string is the port number. Router 2 will translate Type 7 LSAs from the connected domain to Type 5 routes into the backbone. UsethiscommandtodisplaySNMPtrafficcountervalues. Before authentication succeeds, no traffic is forwarded onto the network. When flood control is enabled on a port, incoming traffic is monitored over one second intervals. STP Operation Rapid Spanning Tree Operation Rapid Spanning Tree (RSTP) optimizes convergence in a properly configured network by significantly reducing the time to reconfigure the networks active topology when physical topology or configuration parameter changes occur. Link Aggregation Overview Single Port Attached State Rules By default, a LAG must contain two or more actor and partner port pairs for the LAG to be initiated by this device. Chapter 2: Configuring Switches in a Stack, Chapter 6: Discovery Protocol Configuration, Chapter 14: Logging and Network Management, Appendix A: Policy and Authentication Capacities. All routers with the same VRID should be configured with the same advertisement interval. set inlinepower mode {auto | manual} auto (default) Available power is distributed evenly to PoE modules based on PoE port count. Configuring IPv4 ACLs Procedure 24-1 describes how to configure IPv4 standard and extended ACLs. Switch (config-if)#ip address {your ip address} {mask} Switch (config-if)#no shutdown Configuration of default gateway takes place in the configuration mode and the command does not include the mask for the ip. Specification Guide (English) Quick Setup Guide (English) User Manual (English) Installation Instruction (English) DFE (PLATINUM) WITH 60 10 100 1000BASE-T 7G4202-60 MAC Locking You can configure the switch to issue a violation trap if a packet arrives with a source MAC address different from any of the currently locked MAC addresses for that port. Figure 10-2 Authenticating Multiple Users With Different Methods on a Single Port Authentication Method 802. Terms and Definitions 10-30 Configuring User Authentication. Determines if the keys for trap doors do exist. This sets the port VLAN ID (PVID). 2 ipsourcesocket Classifies based on source IP address and optional post-fixed L4 TCP/UDP port. Determine where DHCP clients will be connected and enable DHCP snooping on their VLANs. Stops any pending grafts awaiting acknowledgments. The key that SNMP is looking for is the notification entry created with the set snmp notify command. Configuring DVMRP System1(su)->router#configure Enter configuration commands: System1(su)->router(Config)#ip igmp System1(su)->router(Config)#ip dvmrp System1(su)->router(Config)#interface vlan 1 System1(su)->router(Config-if(Vlan 1))#ip address 192.0.1.2 255.255.255. The allocation mechanism attempts to maximize aggregation, subject to management controls. User Manuals, Guides and Specications for your Enterasys C5K175-24 Switch. Chapter 23, Configuring VRRP Configure IPv6 Chapter 25, Configuring and Managing IPv6 Security and General Management Configure Access Control Lists (ACLs). Optionally, set the GARP join, leave, and leaveall timer values. Use the no command to reset the IGMP last member query interval to the default value of 1 second. Configure NetFlow to Manage Your Cisco Switch (Optional) 1. Use the advertise-interval command to change the advertise-interval for this VRID. 6. Configuring VRRP Router 2(su)->router(Config-router)#exit Multiple Backup VRRP Configuration Figure 23-3 shows a multi-backup sample configuration. Procedure 17-1 Step Task Command(s) 1. Downloading New Firmware or just want to verify the contents of the images directory, refer to Deleting a Backup Image File on page 1-5 for more information. for me it was ge.1.x. Configuration Guide Firmware 6.61.xx and Higher. (Optional) Configure the allocation mode for system power available for PoE. 1. Switch Configuration Using CLI Commands Guidelines for Rackmount Installation Attaching Brackets and Installing in Rack About SecureStack Switch Operation in a Stack 44 Recommended Procedures to Install New and Existing Stacks Installing a New Stackable System of Up to Eight Switches Adding a New Switch to an Existing Stack Important Weighted fair queuing assures that each queue will get at least the configured percentage of bandwidth time slices. sFlow Using sFlow in Your Network The advantages of using sFlow include: sFlow makes it possible to monitor ports of a switch, with no impact on the distributed switching performance. If you want to change the default timeout value for a specific server or all servers, you must enter the set tacacs server command using the timeout parameter. (1800 seconds) preference level The preference value for this advertised address. Configuring Authentication Optionally Enable Guest Network Privileges With PWA enhanced mode enabled, you can optionally configure guest networking privileges. Supervise the activation of network interfaces on access switches, support the default . Using the all parameter will display all default and non-default configuration settings. set port inlinepower port-string {[admin {off | auto}] [priority {critical | high | low}] [type type]} admin Enables (auto) or disables (off) PoE on a port. Procedure 25-5 Neighbor Discovery Configuration Step Task Command(s) 1. trap | inform3 Unsolicited message sent by an SNMP agent to an SNMP manager when an event has occurred. Telnet Overview on page 4-23 Configure the Secure Shell V2 (SSHv2) client and server. Can you upload files from other sources? Policies will be applied dynamically at authentication using a RADIUS authentication server and the Filter-ID attribute. This configuration requires a charging circuit to charge the DC capacitors of the modules in a controlled way. Download Configuration manual of Enterasys C2H124-24 Switch for Free or View it Online on All-Guides.com. Enabling Master Preemption By default, a router is enabled to preempt a lower priority master for the configured virtual router. RADIUS Management Authentication Procedure 26-2 Configuring IPsec Step Task Command(s) 1. Table 6-1 6-8 File Management Commands Task Command List all the files stored on the system, or only a specific file. PAGE 2. Procedure 4-4 DHCP Server Configuration on a Non-Routing System Step Task Command(s) 1. Actively sending IGMP query messages to learn locations of multicast switches and member hosts in multicast groups within each VLAN. When the boot up output is complete, the system prints a Username prompt. Implementing VLANs building has its own internal network. Managing the Firmware Image Setting the Boot Firmware Use the show boot system command to display the image file currently configured to be loaded at startup. Configuring PoE Procedure 7-3 PoE Configuration for G-Series Devices (continued) Step Task Command(s) 4. Note: When configuring any string or name parameter input for any command, do not use any letters with diacritical marks (an ancillary glyph added to a letter). When operating in unicast mode, optionally change the poll interval between SNTP unicast requests. (See Overview on page 18-12 for more information.) Port Mirroring LAG ports can be a mirror source port, but not a mirror destination port. Network Engineer Network Engineering Description A network engineer is a technology professional who is highly skilled in maintaining the connectivity of networks in terms of. Configuring VLANs Procedure 9-1 Static VLAN Configuration (continued) Step Task Command(s) 7. Use the following commands to review, re-enable, and reset the Spanning Tree mode. 1.1 IP phone ge. ENTERASYS MATRIX-V V2H124-24 CONFIGURATION MANUAL Pdf . 9 Configuring VLANs This chapter describes how to configure VLANs on Enterasys fixed stackable and standalone switches. This guest policy provides for an internet-only access to the network. The hardware, firmware, or software described in this document is subject to change without notice. set lacp aadminkey port-string value 5. All operational ports which are not root, alternate or backup are designated ports. Saving the Configuration and Connecting Devices C5(su)->show ssh SSH Server status: Enabled 2. BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. Configuring Syslog Displaying Current Application Severity Levels To display logging severity levels for one or all applications currently running on your device: show logging application {mnemonic|all} Example This example shows output from the show logging application all command. Transmit Queue Monitoring If no additional power losses occur on the PoE devices and no additional link flapping conditions occur, the network administrator disables link flap detection on the PoE ports. Interpreting Messages For more information on how to configure these basic settings, refer to Syslog Command Precedence on page 14-8, and the Configuration Examples on page 14-12. CoS Hardware Resource Configuration Inbound Rate Limiting Port Configuration Entries ---------------------------------------------------------------------Port Group Name : Port Group :1 Port Type :0 Assigned Ports :ge.1. 3 CLI Basics This chapter provides information about CLI conventions for stackable and standalone switches and CLI properties that you can configure. View online Configuration manual for Enterasys C2H124-24 Switch or simply click Download button to examine the Enterasys C2H124-24 guidelines offline on your desktop or laptop computer. SNMP Support on Enterasys Switches Table 12-1 SNMP Message Functions (continued) Operation Function get-response Replies to a get-request, get-next-request, and set-request sent by a management station. interface {vlan vlan-id | loopback loopbackid } 2. IP Broadcast Settings specific network or subnet. Port Configuration Overview vlan for vlan interfaces lag for IEEE802.3 link aggregation ports Where unit_or_slotnumber can be: 1 - 8 for stackable switches (up to 8 units in a stack) 1 - 3 for I-Series standalone switches (Note that the uplink ports are considered to be slot 3) 1 - 4 for G-Series standalone switches Where port number depends on the device. When console-only access is configured, all TCP SYN packets and UDP packets are dropped, with the exception of UDP packets sent to the DHCP Server or DHCP Client ports. DHCPv6 Configuration Default Conditions The following table lists the default DHCPv6 conditions. set sflow receiver index ip ipaddr 3. sFlow Table 18-7 lists the commands to display sFlow information and statistics. Configuring Authentication Authentication Required Authentication methods are active on the port, based on the global and per port authentication method configured. Table 13-2 LLDP Show Commands Task Command Display LLDP configuration information. MultiAuth mode Globally sets MultiAuth for this device. Thisexampleshowshowtodisplayinformationaboutallswitchunitsinthestack: Thisexampleshowshowtodisplayinformationaboutswitchunit1inthestack: Thisexampleshowshowtodisplaystatusinformationforswitchunit1inthestack: Usethiscommandtodisplayinformationaboutsupportedswitchtypesinthestack. set ipsec authentication {md5 | sha1} Note: This command is not available if the security mode setting is C2. VRRP Overview Figure 23-1 Basic VRRP Topology VRID 1 172.111.1.1 Router R1 Router R2 ge.1.1 VLAN 111 172.111.1.1/16 ge.1.1 VLAN 111 172.111.1.2/16 Host 1 172.111.1.100/16 Default Gateway 172.111.1.1 Figure 23-1 shows a basic VRRP topology with a single virtual router. Table 14-1 Syslog Terms and Definitions Term Definition Enterays Usage Facility Categorizes which functional process is generating an error message. After the switch resets, return to global router configuration mode, create the ACL and define the rules. Management Authentication Notification MIB Functionality Refer to the CLI Reference for your platform for detailed information about the commands listed below in Procedure 5-4. DHCP snooping forwards valid DHCP client messages received on non-routing VLANs. Switch# Switch#conf t Switch (config)#ip default-gateway {ip address} and set passwords. Removing Units from an Existing Stack Use clear ip address to remove the IP address of the stack. Configure an RMON filter entry. To determine if all these elements are in place, the SNMP agent processes a device configuration as follows: 1. Be sure that your serial connection is set properly: Baud rate: 115200 bps (for 5420, 5520, X435, X465, X590, X690, X695, and X870 models) Baud rate: 9600 bps (for other models) Data bits: 8 Stop bit: 1 Parity: none Flow control: none The switch can enforce a system-wide default for password aging (set system password aging). Optionally, enable single port LAGs on the device. Getting Help The following icons are used in this guide: Note: Calls the readers attention to any item of information that may be of special importance. Configuring OSPF Areas The virtual-link is treated as if it were an unnumbered point-to-point network belonging to the backbone and joining the two ABRs. This is useful for troubleshooting or problem solving when network management through the console port, telnet, or SSH is not feasible. Neighbor Discovery Overview There are two primary LLDP-MED device types (as shown in Figure 13-2 on page 13-5): 13-4 Network connectivity devices, which are LAN access devices such as LAN switch/routers, bridges, repeaters, wireless access points, or any device that supports the IEEE 802.1AB and MED extensions defined by the standard and can relay IEEE 802 frames via any method. Using Multicast in Your Network Figure 19-1 IGMP Querier Determining Group Membership IGMP Querier IGMP Query IGMP Membership IGMP Membership Router for 224.1.1.1 Router for 226.7.8.9 Member of 224.1.1.1 Member of 226.7.8.9 As shown in Figure 19-1, a multicast-enabled device can periodically ask its hosts if they want to receive multicast traffic. area area-id default-cost cost 5. then assign the ports you want in each vlan. Port Configuration Overview Table 8-1 Displaying Port Status Task Command Display whether or not one or more ports are enabled for switching. A designated port may forward with the exchange of two BPDUs in rapid succession. Reviewing SNMP Settings Reviewing SNMP Settings Table 12-5 Commands to Review SNMP Settings Task Command Display SNMPv1/SNMPv2c community names and status. Thisexampleshowshowtodisplaymultipleauthenticationsystemconfiguration: Configuring User + IP Phone Authentication. Policy Configuration Overview regardless of the number of moves, adds, or changes to the policy role, Policy Manager automatically enforces roles on Enterasys security-enabled infrastructure devices. Quality of Service Overview There are up to four areas of CoS configuration depending on what type of hardware resource you want to configure. Basic DVMRP configuration includes the following steps: 1. Therefore, a value of 7 is given the highest priority. Port Configuration Overview maximum number of packets which can be received per second with the set port broadcast command: Maximum packet per second values are: 148810 for Fast Ethernet ports 1488100 for 1-Gigabit ports. DHCPv6 Configuration address, a multicast address, or a link-local address. Display the current settings for the Management Authentication Notification MIB. A code example follows the procedure. set inlinepower detectionmode {auto | ieee} auto (default) The Enterasys device first uses the IEEE 802.3af/at standards resistorbased detection method. Configuring SNMP . Link Aggregation Overview Because port 6 has both a different speed and a higher priority than the port with the lowest priority in the LAG, it is not moved to the attached state. Violating MAC addresses are dropped from the devices (or stacks) filtering database. Figure 15-13 shows that with a single Spanning Tree configuration, only a single link towards the root forwards on a bridge. If Spanning Tree is disabled globally all linked ports will be in a forwarding state and the Spanning Tree Protocol will not run. RFC 3580s RADIUS tunnel attributes are often configured on a RADIUS server to dynamically assign users belonging to the same organizational group within an enterprise to the same VLAN, or to place all offending users according to the organizations security policy in a Quarantine VLAN. Frames will egress as tagged. Authentication Configuration Example In an 802.1x configuration, policy is specified in the RADIUS account configuration on the authentication server using the RADIUS Filter-ID. About This Guide This guide provides basic configuration information for the Enterasys Networks Fixed Switch platforms using the Command Line Interface (CLI0, including procedures and code examples. Since MAC-based authentication authenticates the device, not the user, and is subject to MAC address spoofing attacks, it should not be considered a secure authentication method. 3. Configuring Authentication dynamic Egress formatting will be based upon information contained in the authentication response. In interface configuration mode, configure an IP address for all routing interfaces in the AS. Stackable Switches. For information on the command syntax and parameters, refer to the online help or the CLL Reference for your platform. This. Configuring PoE Procedure 7-3 PoE Configuration for G-Series Devices (continued) Step Task Command(s) 7. Optionally, change the encryption type. Only the Encapsulating Security Payload (ESP) mode of operation is supported. A packet is either forwarded (a permit rule) or not forwarded (a deny rule) according to the first rule that is matched. 2. Configuration Guide. TACACS+ You can also configure TACACS+ to use a single TCP connection for all TACACS+ client requests to a given TACACS+ server. sFlow Table 18-3 describes how to manage remote network monitoring. Configuring PoE Stackable B5 and C5 Devices Procedure 7-2 PoE Configuration for Stackable B5 and C5 Devices Step Task Command(s) 1. Quality of Service Overview Preferential Queue Treatment for Packet Forwarding There are three types of preferential queue treatments for packet forwarding: strict priority, weighted fair, and hybrid. On I-Series only, display contents of memory card. Tabl e 2010providesanexplanationoftheshowippimsminterfacestatscommandoutput. A sampler instance performs packet flow sampling on the data source to which it is configured. This information is used to determine the module port type for port group. Enter router interface configuration command mode for the specified interface from global configuration command mode. show port status [port-string] Display port counter statistics detailing traffic through the device and through all MIB2 network devices. Thischapterdescribesswitchrelatedloggingandnetworkmanagementcommandsandhowto usethem. The following example inserts a new entry into IPv4 extended ACL 121 before entry 2. installation and programing guide and user manuals. PIM-SM adopts RPF technology in the join/prune process. Note Do not use hardware flow control. Using the Command Line Interface Logging In By default, the switch is configured with three user login accountsro for Read-Only access, rw for Read-Write access, and admin for super-user access to all modifiable parameters. When operating in unicast mode, optionally change the number of poll retries to a unicast SNTP server. Configuring Policy Procedure 16-1 Step Configuring Policy Roles (continued) Task Command egress-vlans (Optional) Specifies the port to which this policy profile is applied should be added to the egress list of the VLANs defined with this parameter. show tacacs session {authorization | accounting} [state] Displays only the current status for TACACS+ per-command authorization and accounting. MAC Locking If a connected end station exceeds the maximum values configured with the set maclock firstarrival and set maclock static commands (a violation). Router: Calls the readers attention to router-specific commands and information. C5(rw)->set dhcp pool manual3 client-identifier 01:00:01:22:33:44:55 C5(rw)->set dhcp pool manual3 host 10.12.1.10 255.255.255.0 C5(rw)->set dhcp pool manual3 lease infinite Configuring Additional Pool Parameters Table 4-8 lists the commands that can be used to configure additional IP address pool parameters. Ctrl+E Move cursor to end of line. DHCP and BOOTP Relay DHCP/BOOTP relay functionality is applied with the help of UDP broadcast forwarding. Policy Configuration Overview Examples This example assigns a rule to policy profile 3 that will filter Ethernet II Type 1526 frames to VLAN 7: C5(su)->set policy rule 3 ether 1526 vlan 7 This example assigns a rule to policy profile 5 that will forward UDP packets from source port 45: C5(su)->set policy rule 5 udpsourceport 45 forward This example assigns a rule to policy profile 1 that will drop IP source traffic from IP address 1.2.3.4, UDP port 123. Optionally, remove a static route. Understanding How VLANs Operate Shared Virtual Local Area Network (VLAN) Learning (SVL): Two or more VLANs are grouped to share common source address information. Assign the new super-user account as the emergency access account. Globally: Disabled. Quality of Service Overview Additional port groups, up to eight (0 through 7) total, may be created by changing the port group value. 1. Notice Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice. show ip dvmrp [route | neighbor | status] Display the IP multicast routing table. Table 26-3 show macauthentication Output Details. Default settings are listed in Table 15-6: Table 15-6 Spanning Tree Port Default Settings Setting Default Value Bridge priority mode 802. For information about upgrading firmware on a new stack, refer to Configuring a Stack of New Switches on page 1-8. Use the passive-interface command in router configuration command mode to configure an interface as passive or to set passive as the default mode of operation for all interfaces. Decides if the upstream neighbor is capable of receiving prunes. The read er should in all cases consult Enterasys Networks to determine whether any such Configuring CLI Properties 3-8 CLI Basics. Configuring Link Aggregation This section provides details for the configuration of link aggregation on the N-Series, S-Series, stackable, and standalone switch products. RMON Table 18-1 RMON Group Event RMON Monitoring Group Functions and Commands (continued) What It Does What It Monitors CLI Command(s) Controls the generation and notification of events from the device. RSTP bridges receiving MSTP BPDUs interpret them as RSTP BPDUs. Ctrl+H Delete character to left of cursor. sFlow 2. Connect a null-modem DB9 to DB9 cable between the computer's serial port and the switch; use serial communication settings 9600, n, 8, 1. For an IPv6 ACLs, the following protocols can be specified in a rule: Any IPv6 protocol Transmission Control Protocol (TCP) User Datagram Protocol (UDP) IPv6 Internet Control Message Protocol (ICMPv6) TCP and UDP rules can match specific source and destination ports. i Notice Enterasys Networks reserves the right to make changes in specif ications and other information co ntained in this document and its web site without prior notice. For example, for a network with the address 192.168.0.0/16, the directed broadcast address would be 192.168.255.255. Any such invalidity, illegality, or unenforceability in any jurisdiction shall not invalidate or render illegal or unenforceable such provision in any other jurisdiction. Setting target addresses to control where SNMP notifications are sent 6. (B3 platforms only) EAPOL Disabled. Basic PIM-SM configuration includes the following steps: 1. The CIST root may be, but is not necessarily, located inside an MST region. When changing between Normal and FIPS mode, a system reboot is required, indicated by a warning message: Warning: Changing the security profile requires system reset. First, the module is verified as present in Slot 2, and the port status is shown as operating as a 1000BASE-SX port. The sources DR registers (that is, encapsulates) and sends multicast data from the source directly to the RP via a unicast routing protocol (number 1 in figure).